Welcome to ZJ·BETTER
English 中文
FAQ
Product
  • integrated lift pumping station
  • integrated lift pumping station
  • integrated lift pumping station
  • integrated lift pumping station
  • integrated lift pumping station
  • integrated lift pumping station
  • integrated lift pumping station
  • integrated lift pumping station
  • integrated lift pumping station
  • integrated lift pumping station
integrated lift pumping station
integrated lift pumping station
integrated lift pumping station
integrated lift pumping station
integrated lift pumping station

integrated lift pumping station

The integrated lifting pump station is a kind of sewage treatment device mainly used in municipal industrial basement drainage, subway drainage, living areas, factories, etc. below the ground
Print this page
Share:
Product Description
Introduction
 The integrated sewage pumping station is an ideal substitute for traditional sewage pumping stations. In general, the traditional pumping station has strict requirements for planning and construction. Every detail needs to be planned, and the installation of the pumping station also requires a lot of manpower, material resources and time. It is necessary to arrange the construction site and pour it with concrete. It takes a lot of time to wait for the concrete to harden. Then you must determine the inlet point, drill holes, and install the necessary components. It takes at least 2 months to complete these processes. In the construction process of the pumping station, it is also necessary to cooperate with the contractor of each process. These unnecessary processes will consume a lot of energy of the planners, and the quality of the project of each contractor will also be uneven.
The integrated sewage prefabricated pumping station mainly uses a sewage treatment device below the ground in the municipal industrial basement drainage, subway drainage, living area, factory and so on.
Model meaning:
 PPS 08 × 22 / 0.39 - 2 / SS
① ② ③ ④ ⑤ ⑥

1. Integrated prefabricated pumping station
2. Wellbore diameter
08=Φ800mm
10=Φ1000mm
12=Φ1200mm
20=Φ2000mm
38=Φ3800mm

3. Shaft height (length, depth): the height of the entire cylinder indicated (without accessories)
22=2200mm
25=2500mm
60=6000mm
130=13000mm
4.Pump station effective volume(m3)
5. The number of pump stations equipped with water pumps: 2 (can be equipped with 2-4 sets)
6. Material of the conveying pipe
Stainless steel 304SS, Carbon steel or Plastic pipe
Environment and working conditions:
 ·The ambient temperature should be -40 °C ~ 40 °C.
·The relative humidity is preferably 25% to 85%, and the anhydrous beads are condensed.
·The water medium delivered by the pumping station should meet the following requirements:
The temperature should be -5 °C ~ 70 °C;
PH value should be 4~10; (over-range use should be made at the time of ordering)
The maximum diameter of the particles in the conveying medium should be smaller than the diameter of the selected water pump.
·Power supply:
380V (±10%), 3-phase five-wire system, 50Hz (±5%);
220V (±10%), single phase, 50Hz (±5%).
·Vibration: <0.5g, vibration frequency 10Hz-50Hz maximum vibration acceleration should not exceed 5m / s2.
·The equipment operation location is generally applied to non-conductive or explosive dust (for occasions where the environment is required, please make an order when ordering, you can configure explosion-proof submersible pump (ExdI, ExdIIAT4, ExdIIBT4, ExdIICT4) or explosion-proof control cabinet, no corrosive metal or damage insulation gas or steam.
Structure:
 

Performance parameter list:
 
Model Staion Flow Pump flow Pump 5 min flow Start/close times effective volume Diameter liquid height height weight
m3/day M3/h M3/5min Times/h M3 m m m kg
PPS08X22/0.39-2 259 11 0.9 7 0.4 0.8 0.15 2.2 231
PPS08X22/0.54-2 360 15 1.3 7 0.5 0.8 0.21 2.2 231
PPS08X23/0.77-2 518 22 1.8 7 0.8 0.8 0.31 2.3 240
PPS08X24/0.90-2 605 29 2.1 7 0.9 0.8 0.36 2.4 248
PPS08X24/1.03-2 691 29 2.4 7 1.0 0.8 0.41 2.5 248
PPS08X25/1.29-2 864 36 3 7 1.3 0.8 0.51 2.5 254
PPS08X28/1.93-2 1296 54 4.5 7 1.9 0.8 0.77 2.8 278
PPS08X30/2.57-2 1728 72 6 7 2.6 0.8 1.02 3.0 295
PPS10X30/3.21-2 2160 90 7.5 7 3.2 1 1.02 3.0 386
PPS10X31/3.57-2 2402 100 8.3 7 3.6 1 1.14 3.1 396
PPS14X30/4.50-2 3024 126 10.5 7 4.5 1.4 1.02 3.0 531
PPS14X32/5.14-2 3456 144 12 7 5.1 1.4 1.17 3.2 556
PPS18X30/5.79-2 3888 162 13.5 7 5.8 1.8 1.02 3.0 712
PPS18X31/6.43-2 4320 180 15 7 6.4 1.8 1.14 3.1 729
PPS20X31/7.07-2 4752 198 16.5 7 7.1 2 1.13 3.1 1164
PPS30X40/19.29-2 12960 540 45 7 19.3 3 2.05 4.0 2385
PPS40X122/128.57-2 86400 3600 300 7 128.6 4 10.23 12.2 9002
For more specifications, please contact us.


Application cases:

Inquiry
 
Please feel free to submit your inquiry information to us! our sales manager will contact with
you as soon as possible
* Name:
Conutry:
* Email:
Tel:
Type:
Flow:
Head:
Power:
Medium:
* Inquiry: